Ancillaries – Ground Gas
Triton supplies a full range of ancillary products for the installation of ground gas barrier systems. This range includes a venting mat, a Radon sump, primers, tapes and top hats. Situations where the Fillet Seal will be employed should already have been prepared in accordance with the slurry coating or render specification. In the majority on instances, the Fillet Seal will be applied on to the slurry coated surface.
Triton TGS – GV25 Gas Venting Mat
A 25mm thick single-sided, geocomposite that provides a void beneath floor slabs which, when connected to air inlets and outlets, allows sufficient air changes to dilute gases to safe concentrations when designed correctly.
Triton Radon Sump
A perforated sump to allow for the accumulation of gas prior to venting externally via an external in-line extractor fan. Installation of the sump reduces pressure on the installed gas proof membrane and venting outlet.The black polyethylene preformed chamber is designed to be located in the ground or basement floor, finishing flush with the surrounding floor level. It is supplied with a structural polyethylene lid, which is removable and can accept foot traffic.
Triton TWS – EX Primer/TWS – EX Primer LT
A primer for use with TWS-EX100GM membrane in order to consolidate the substrate and ensure complete bond development. Supplied as a single pack, brush applied liquid coating. Coverage – 8 m2 per litre. Available in 5 and 25 litre packs. The ‘LT’ (low temperature) version is classed as moisture tolerant and can be applied to damp or slightly green concrete.
Triton TWS-EX Reinforcing Tape
For use with TWS fully bonded waterproof membranes for the reinforcement of edge and corner details.
Triton TGS-GM500 DS Tape
A double-sided jointing tape for use when installing TGS-GM500 gas barrier. The 50mm x 10m butyl tape has a very low vapour transmission rate and outstanding elongation properties. Should be laid in conjunction with TGS-GM500 Joint Tape. Excellent adhesion qualities.
Triton TGS-GM500 Joint Tape
A single-sided overlap tape for use when installing TGS-GM500 gas barrier. Should be used in conjunction with TGS-GM500 Double Sided tape to create a secondary seal when jointing the membrane. Excellent adhesive properties.
Triton TGS-GM500 Top Hat
TGS Top Hats provide an effective seal where a 110mm pipe penetrates a membrane. Easy to install. Made from quality materials. Hose clip included. Base of Top Hat: 280 x 280mm.
Triton TGS-HCM1000 DS Tape
A double-sided jointing tape for use when installing TGS-HCM1000 gas barrier. Should be laid in conjunction with TGS-HCM1000 Joint Tape. Excellent adhesion qualities.
Triton TGS-HCM1000 Joint Tape
A single-sided overlap tape for use when installing TGS-HCM1000 gas barrier. Should be used in conjunction with TGS-HCM1000 Double Sided Tape to create a secondary seal when jointing the membrane. Excellent adhesive properties.
Triton Fillet Seal
Triton Fillet Seal is a pre-packed cement based and polymer modified product for use as a floor to wall junction seal during waterproofing works when using cementitious slurry coatings such as Triton TT55. In most circumstances, Fillet Seal needs only be mixed with water for use. Where extra adhesion is required, Triton SBR may be used. Note: Where water is leaking or seeping the use of Triton Quick Set is advised.
The use of Fillet Seal helps to ensure a smooth transition between horizontal and vertical surfaces that will minimise the risk of leaving gaps or holes unsealed during the waterproofing works.
Preparation:
Situations where the Fillet Seal will be employed should already have been prepared in accordance with the slurry coating or render specification. In the majority on instances, the Fillet Seal will be applied on to the slurry coated surface.
Triton Fillet Seal is available in 25 kg bags.
Triton LPA
Triton LPA/Primer is a ready to use emulsion that can be used as a surface primer for Triton Repair Mortar, Triton Floor Levelling Compound and Triton TT Vapour Membrane.
Available in 5 litre packs.
